3 set pressure vessel applied to food factory

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

3 set pressure vessel applied to food factory have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


3 set pressure vessel applied to food factory.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
3 set pressure vessel applied to food factory 3 set pressure vessel applied to food factory 3 set pressure vessel applied to food factory

15 ton hours three-pass boiler Pakistan in textile facto

5 ton water tube boiler Pakistan in textile factory 15 ton hours three-pass boiler Pakistan in textile factory 2 set 20ton hot water boiler in textile factory 15 ton hours oil fired hot water boiler applied to food factory

lexie@zozen.com > Get A Quote >

Steam Accumulators - beta.spiraxsarco.c

Surplussing valves can also be fitted directly to the boiler or on the steam main to the factory, as shown in Figure 3.22.3. The set pressure should be: Less than the 'high fire' control pressure, to prevent any interference of the surplussing control with the burner controls. High enough to maintain the pressure in the boiler at a safe level.

lexie@zozen.com > Get A Quote >

Factor of safety - Wikiped

2019-5-28 · Buildings commonly use a factor of safety of 2.0 for each structural member. The value for buildings is relatively low because the loads are well understood and most structures are redundant. Pressure vessels use 3.5 to 4.0, automobiles use 3.0, and aircraft and spacecraft use 1.2 to 3.0 depending on the application and materials.

lexie@zozen.com > Get A Quote >

Certification for Kazakhstan. GOSTK. ROK. Kazak

Certificate with validity for 1 year certificate or certificate for 3 years. They can be issu on the basis of the inspection, along with the relevant documents. In the event of a visit to the factory, our company will set all the plans visit and will be accompanied by our expert professionals and provide them with all

lexie@zozen.com > Get A Quote >

Reverse Osmosis membranes - Lennte

Reverse Osmosis Membranes Lenntech can provide you with membrane elements from most leading membrane producers. In our scope of supply you find tap, brackish and seawater elements.

lexie@zozen.com > Get A Quote >

Chemical Filling, Pressure Vessel from Chin

China Chemical Filling, Pressure Vessel, Compressor, offered by China manufacturer & supplier -Shanghai Shisheng Machinery Manufacturing Co., Ltd., page3

lexie@zozen.com > Get A Quote >

Standards and Certification - AS

2019-6-17 · ASME is the leading international developer of codes and standards associated with the art, science, and practice of mechanical engineering. Starting with the first issuance of its legendary Boiler & Pressure Vessel Code in 1914, ASME's codes and standards have grown to more than 500 offerings currently in print.

lexie@zozen.com > Get A Quote >

B400 Emergency Relief Manway | 3B Contro

All products are factory tested and fully certified. Self Draining All products are designed so that any condensate drains away from seating areas. Low leakage Standard seating design ensures minimum leakage of less than 1 scfh at 90% of set pressure. Internal Parts

lexie@zozen.com > Get A Quote >

What is a stainless steel reactor vessel? - Quo

What is a stainless steel reactor? The stainless steel reactor is composed of the kettle body, the cauldron cover, the jacket, the agitator, the transmission device, the shaft sealing device and the support, etc. When the height of the mixing devi

lexie@zozen.com > Get A Quote >

Hydropneumatic Pressure Vessels | Products &

Universal Air & Gas Products Corp. HydroMAX Program for Pressure Vessels Our HydroMAX program begins with apparatus and vessel testing and ends with your fully recharged pressure vessels, ready for deployment.Certified, factory trained and marine insured, technicians are available for high pressure breathing air or industrial system services. Universal Air & Gas Products (UAPC) fleet vans are

lexie@zozen.com > Get A Quote >

India. The Factories Act - International Labou

(3) Before a factory engaged in a manufacturing process which is ordinarily carried out for less than one hundred and eighty working days in the year, resumes working, thc occupier shall send a written notice to the Chief Inspector containing the particulars specified in sub-section (1) that least thirty days before the date of the commencement

lexie@zozen.com > Get A Quote >