3 types waste heat boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

3 types waste heat boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


3 types waste heat boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
3 types waste heat boiler 3 types waste heat boiler 3 types waste heat boiler

Waste Heat Recovery System - an overview

Waste heat boilers to be used for generating power should be designed to take these factors into account. The location of the WHB with regard to the system dust collector assumes importance. 2.5. Waste heat available from vent gases from clinker cooler. Air is used to cool clinker coming out of the kiln at around 1400 °C in all types of coolers.

lexie@zozen.com > Get A Quote >

Waste -- Z

2019-4-26 · Waste heat boilers developed by our company recycle and reuse waste energy according to the production characteristics of various industries. Product Types Carbon Rotary Kiln Waste Heat Boiler 2 - 45 t/1.4-31.5 MW

lexie@zozen.com > Get A Quote >

Waste heat recovery unit - Wikiped

2019-6-6 · A waste heat recovery unit (WHRU) is an energy recovery heat exchanger that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. The WHRU is a tool involved in cogeneration.Waste heat may be extracted from sources such as hot flue gases from a diesel generator, steam from cooling towers, or even waste

lexie@zozen.com > Get A Quote >

Waste Heat Recovery Boiler - Waste Heat Boiler

Waste heat boilers are the significant energy saving equipment, utilize the heat in flue gases from combustion processes or hot extract air from industrial processes to generate hot water or saturated steam Otherwise, the waste heat boiler could be used in oil gas fired combined cycle units, and take advantage of the high temperature flue gas heat discharged by gas turbine

lexie@zozen.com > Get A Quote >

shell types waste heat boiler – High Efficiency Oi

Shell and tube heat exchanger – Wikipedia. A shell and tube heat exchanger is a class of heat exchanger designs. It is the most common type of heat exchanger in oil refineries and other large chemical GM Boiler – The Ultimate Steam SolutionAgro Waste Fired Boiler.

lexie@zozen.com > Get A Quote >

Waste Heat Boilers - Clarke Ener

2019-6-16 · Waste Exhaust Heat Boilers. Approximately 25% of the usable energy of the fuel gas is released in the exhaust of the gas engine. This can be captured for cogeneration in a combined heat and power plant. This heat exits the engine at ~450 o C as 'high grade heat', contrasting to 'low-grade heat' available from the generator cooling circuits. This high temperature and flow makes it well

lexie@zozen.com > Get A Quote >

shell types waste heat boiler – High Efficiency Oi

Shell and tube heat exchanger – Wikipedia. A shell and tube heat exchanger is a class of heat exchanger designs. It is the most common type of heat exchanger in oil refineries and other large chemical GM Boiler – The Ultimate Steam SolutionAgro Waste Fired Boiler.

lexie@zozen.com > Get A Quote >

Waste heat recovery boiler -- ZBG Boil

2019-5-23 · The Chemical Industry Waste Heat Boiler developed by ZBG mainly have vertical and tunnel kiln horizontal two types of natural circulation waste heat boilers, which can be integrated with the three-waste co-firing furnace and the blow-off gas furnace, so that the production enterprises can fully realize "two "Coal becomes a coal" and "two furnaces become a furnace" is a typical energy-saving

lexie@zozen.com > Get A Quote >

Global Horizontal Waste Heat Boiler Market B

Horizontal Waste Heat Boiler Market report covers size, share and forecast (value and volume) by regions, top players, product types and applications, with historical data along with forecast from 2019 to 2026; The report covers an in depth description, competitive scenario, wide product portfolio of key vendors and business strategy adopted by

lexie@zozen.com > Get A Quote >

Waste Heat Recovery System - an overview

Waste heat boilers to be used for generating power should be designed to take these factors into account. The location of the WHB with regard to the system dust collector assumes importance. 2.5. Waste heat available from vent gases from clinker cooler. Air is used to cool clinker coming out of the kiln at around 1400 °C in all types of coolers.

lexie@zozen.com > Get A Quote >

Features of TAKUMA Waste Heat Boiler | Waste Hea

2018-11-6 · Features of TAKUMA Waste Heat Boiler | Waste Heat Boiler | Municipal solid waste treatment plants, Boiler plants | TAKUMA Takuma waste heat boilers are designed to select optimum boiler types with full consideration for waste gas condition, steam condition, operation mode, installation space and various other factors, ensuring to maintain

lexie@zozen.com > Get A Quote >